Vanne papillon d'eau Elephant WBV1632E-2W-Fb-H, matériau du corps - fo – Valve Elephant
Elephant  |  SKU : D050-30862

Vanne papillon d'eau Elephant WBV1632E-2W-Fb-H, matériau du corps - fonte QT450, matériau du disque - acier inoxydable AISI 316L, joint - EPDM, actionneur pneumatique PA-DA double action, 4M310-08 24V, BKV APL-210N, volant HDM

€494,74
Taxes incluses Frais de livraison calculés lors du paiement.

Livraison et expédition

Les frais de livraison sont déterminés lors du processus de paiement et varient en fonction de plusieurs facteurs, notamment le type de produit, le délai de livraison, le fournisseur de services et le pays de destination.

Si vous avez des questions sur nos produits, nos options de livraison ou toute autre chose, n'hésitez pas à nous contacter.

Description

The WBV1632E-2W-Fb butterfly valve is designed for use as a shut-off or control valve to control flows in heat supply systems, water supply, in technological processes in the food, chemical, oil and gas, pulp and paper and other industries. Operating principle: The valves open and close by turning the disk by 90°. Opening is performed by turning the handle counterclockwise, closing - clockwise. 

Pneumatic actuators PA-DA are designed to automate the process of controlling industrial shut-off valves - valves, ball valves. Elephant pneumatic actuators are designed for use both indoors and outdoors. All internal and external parts have an anti-corrosion coating.

The manual doubler with worm gear and HDM reduction gear allows manual setting of the required positioning of the shut-off element by a quarter turn, acting as an alternative to pneumatic, electric or hydraulic quarter-turn actuators. Suitable for both indoor and outdoor installation. The modular design of the manual doubler is intended to ensure the most efficient and effective.

The APL-210N limit switch unit is designed for visual and electrical signaling of the end positions of the valve shut-off element. It is installed on top of the surface of the pneumatic drive and connected to the drive shaft - DIN standard. In a sealed box, as a rule, there are two sensors that track the position of the drive shaft and signal in extreme positions. Visual indication of the position can be observed on the body of the unit there is a 3D visual indicator RED - CLOSED and YELLOW - OPEN.

 

 

Technical characteristics of butterfly valves Elephant WBV1632E-2W-Fb-H, body material - cast iron QT450, disk material - stainless steel AISI 316L, seal - EPDM, pneumatic actuator PA-DA double action, 4M310-08 24V, APL-210N, handwheel HDM

Parameter Meaning
Nominal diameter DN, mm 40 - 300
Nominal pressure PN, bar 16
Temperature of working environment t, ⁰C from -20 to +110
Working environment water, steam, aggressive environments and
liquids with abrasive content (cement, sand, alumina, etc.)
Direction of flow bilateral
Control type DN40-200 - handle
DN250-300 - reducer
Connection to the pipeline interflange
Body material cast iron QT450
Seal material EPDM with wear-resistant coating
Service life, years 10

 

 

Sketch of parts of rotary disc valves Elephant WBV1132N-2W-Fb DN40-300 PN16

 

General details and materials of butterfly valves Elephant WBV1132N-2W-Fb DN40-300 PN16

No. Part name Material
1 Frame cast iron QT450
2 Disk Stainless steel 316L
3 Saddle seal EPDM
+ wear-resistant material
(siliclone+graphite)
4 Stock steel 2Cr13

 

 

Sketch of dimensions of butterfly valves Elephant WBV1132N-2W-Fb DN40-300 PN16

 

General weight and dimensions of the Elephant WBV1132N-2W-Fb butterfly valves DN40-300 PN16

DN L H H1 D2 D1 n.d.
DN40 43 147 70 92 125 4- Ø23
DN50 43 147 70 92 125 4- Ø23
DN65 46 155 76 110 145 4- Ø23
DN80 46 164 92 121 160 8- Ø20
DN100 52 175 106 153 180 4- Ø23
DN125 56 194 119 176 210 4- Ø23
DN150 56 206 132 207 240 4- Ø25
DN200 60 237 162 259 295 4- Ø25
DN250 68 282 200 316 355 4-Ø28
DN300 78 311 225 370 410 4-Ø28

 

 


Technical data of DA double-acting pneumatic actuators:

Type of pneumatic actuator DA - double-acting
Nominal pressure PN, bar 12
Working pressure, bar 2...8
Working medium filtered compressed air
Maximum particle diameter of the working medium, µm2 ≤30
Ambient temperature, ⁰C -20 to +80
Swivel angle, ° 0 - 90
Swivel angle adjustment, % ±5
Position indicator open/closed
Top connection standard NAMUR
Air connection standard NAMUR
Average life, cycles closed/open 70 000 (for non-aggressive media and medium pressure and temperature values)


DA pneumatic actuators double-acting rotary actuators

 


Dimensions and mounting dimensions of DA double-acting pneumatic actuators:

Model A, mm B, mm C, mm D, mm E, mm F, mm G, mm H, mm
DA-052 30 41,5 65,5 72 92 65 30 80
DA-065 36 47 81 88 108 72 30 80
DA-083 46 57 98,5 108,7 128,7 92 30 80
DA-105 57,5 64 122,5 133 153 109,5 30 80
DA-130 67,5 74,5 145,5 155 185 127,5 30 130
DA-140 75 77 161 172 202 137,5 30 130
DA-160 87 87 184 197 227 159 30 130
DA-210 113 113 235,5 255 285 210 30 130
DA-270 147 147 299 326 356 273 30 130
DA-300 162 174 330 350 380 312 30 130
DA-350 190 195 483 410 440 365 30 130

 

Model I, mm J, mm M, mm N, mm Z, mm d, mm K L
DA-052 36 50 11x11 14 147 40 M5x8 M6x10
DA-065 50 70 14x14 18 168 40 M6x10 M8x13
DA-083 50 70 17x17 21 204 40 M6x10 M8x13
DA-105 70 102 22x22 26 268 40 M8x13 M10x16
DA-130 70 102 22x22 26 301 55 M8x13 M10x16
DA-140 102 125 27x27 31 390 55 M10x16 M12x20
DA-160 102 125 27x27 31 458 55 M10x16 M12x20
DA-210 - 140 36x36 40 532 80 - M16x25
DA-270 - 165 46x46 50 718 80 - M20x25
DA-300 - 165 46x46 50 760 80 - M20x25
DA-350 165 254 46x46 50 920 80 M20x25 8xM16x25

Sketch of dimensions of DA double-acting pneumatic actuators

 

 

Materials of parts for DA double-acting pneumatic actuators:

№ Part name Material
1 Indicator screw ABS plastic
2 Position indicator ABS plastic
3 Spring clip stainless steel 304
4 Metal washer stainless steel 304
5 Pressure washer engineering plastic
6 Housing hard anodized extruded aluminum alloy
7 Pressure washer engineering plastic
8 Limiter alloy steel
9 Shaft sealing ring upper NBR
10 Upper shaft sliding ring engineering plastic
11 Shaft nickel plated alloy steel
12 Shaft sliding ring lower engineering plastic
13 Shaft O-ring lower NBR
14 Plug NBR
15 Seal ring of adjusting screws NBR
16 Washer of adjusting screw stainless steel 304
17 Lock nut of adjusting screw stainless steel 304
18 Adjusting screw stainless steel 304
19 Piston die-cast aluminum alloy
20 Piston guide plate engineering plastic
21 Piston sliding ring engineering plastic
22 Piston O-ring NBR
23 Spring set spring steel
24 Cover O-ring NBR
25 End cap cast aluminum with polyester coating
26 Cover screw stainless steel 304
27 Stop screw stainless steel 304
28 Adapter carbon steel

Material sketch of DA double-acting pneumatic actuators

 

 

Technical characteristics of the pneumatic distributor 4M310-08 NAMUR

Design Spool-type
Test pressure (body strength test. Not for operation!), bar 10
Working pressure (recommended range for normal operation), bar 1.5 ÷ 8
Valve type 5/2 five-port, two-position
Working medium purified air (40 µm filter fineness)
Operating temperature, °C 0 to +60
Actuation frequency 5 cycles per second
Manual override yes
Protection rating/insulation class IP65/F
Connection to pneumatic actuator NAMUR-compliant mounting surface (VDI/VDE3845)
Body material anodized aluminum
Effective cross-sectional area, mm2 25 (Cv = 1.4)
Exhaust port dimensions (vent to atmosphere) 2 - PT1/4”
Air inlet port size (to pneumatic valve) G1/4”
Air outlet port size (to pneumatic actuator) 2 x Ø19.2 mm
Response time, sec 0.05
Supply voltage, V 220AC/24DC
Coil power 220VAC – 5.5 VA/24VDC – 4.8 W
Weight, kg 0.35
Average service life, cycles 10,000,000

 

 

Overall and installation dimensions of the pneumatic distributor 4M310-08 NAMUR

A C D E F G H I K L J N M
mm
40 24 28 32 40 21,5 69 45 17,5 135 29,3 40 27

Sketch of the dimensions of the pneumatic distributor 4M310-08 NAMUR

 

 

Basic materials and parts of the pneumatic distributor 4M310-08 NAMUR

№ Part Name Material
1 Connector Engineering plastic
2 Nut POM + carbon steel
3 Coil Copper
4 Control Elements —
5 Plate Carbon steel
6 Piston POM
7 Control Valve Seat Engineering plastic
8 Valve Body Aluminum alloy
9 Spool Aluminum alloy
10 O-Ring Seal HNBR
11 Rear Cover Engineering plastic
12 Filter Synthetic material
13 Piston POM
14 Spring Stainless steel
15 Manual Override Engineering plastic
16 Rear Seat Aluminum alloy
17 Spring Seat Aluminum alloy
18 Type C Towing Shackle 65Mn

Sketch of the dimensions of the pneumatic distributor 4M310-08 NAMUR

 

 

Sketch of dimensions of manual backups Elephant-HDM

 

General weight and dimensions of manual backup valves Elephant-HDM

Model D2, mm A, mm T, mm Y, mm H, mm S, mm Steering wheel diameter, mm Weight, kg
HDM-1 70 90 44 145 120 53 180 3
HDM-2 102 125 62.5 178 133 56.5 200 4.5
HDM-3 125 140 70 212 180 68.7 280 6.9
HDM-4 125 188.5 94 280 195 84 320 13.7

 

 

Limit Switch Block Elephant APL-210N 

 

Characteristics of the limit switch unit Elephant APL-210N

Parameter Meaning
Protection All-weather IP65

Ambient temperature 		From -40°C to +80°C
Cable entry thread 2 x NPT1/2”
Terminal block 8 cells 0.08-2.6mm²
Voltage 12V, 24V, 38V, 48V, 110V, 220V,
250V
Indicator position CLOSED: red OPEN: green
Sensor 2 SPDT Electromechanical Microswitches OMRON
V151-1C25
External coating Polyester coating
(black)
Shaft Standard shaft (17mm)

Avis (0)

Documentation
nullPneumatic valve ELEPHANT 4M310-08 spool type
nullButterfly valve for abrasive media Elephant WBV1632E-2W-Fb-H DN40-200 16 bar cast iron interflanged with handle
nullPneumatic rotary actuator ELEPHANT PA-x-x double-acting and with return springs

Paiement et sécurité

Moyens de paiement

    Vos informations de paiement sont gérées de manière sécurisée. Nous ne stockons ni ne pouvons récupérer votre numéro de carte bancaire.

    Variantes disponibles

    SKU Taille de la connexionPressionPrix DisponibilitéQuantité Ajouter au panier
    D050-30862DN10016 bars €494,74 Épuisé
    D050-30863DN12516 bars €647,81 Épuisé
    D050-30864DN15016 bars €809,54 Épuisé
    D050-30865DN20016 bars €1.036,51 Épuisé
    D050-30858DN4016 bars €494,85 Épuisé
    D050-30859DN5016 bars €505,12 Épuisé
    D050-30860DN6516 bars €514,62 Épuisé
    D050-30861DN8016 bars €479,79 Épuisé

    Questions fréquemment posées

    Expédition

    Dans quels pays expédiez-vous ?

    Nous proposons actuellement des livraisons en France et dans toute l'UE, ainsi que des options de livraison internationales. Si vous avez une destination spécifique en tête qui n'est pas répertoriée, n'hésitez pas à nous contacter pour plus d'informations.

    Combien de temps faudra-t-il pour recevoir ma commande ?

    L'expédition standard prend normalement 3 à 7 jours. L'expédition le lendemain est disponible pour toutes les commandes nationales (moyennant des frais supplémentaires). Les délais d'expédition internationaux dépendent des produits et de la destination (estimés au moment du paiement).

    Retours et remboursements

    Comment retourner un produit ?

    Les articles doivent être retournés dans les 30 jours suivant la réception de votre commande. Les articles doivent être retournés dans le même état dans lequel ils ont été reçus, ne pas être portés/utilisés, avoir toutes les étiquettes encore attachées et inclure tous les emballages d'origine.

    Combien de temps faudra-t-il pour recevoir mon remboursement ?

    Les remboursements sont traités dans les 7 jours suivant la réception des articles.